Thursday, June 14, 2012

Entry 14: Meeting With Mentor (9)

14 June 2012

Today, our meeting was about the new prototype design.

Previously, we had formulated the basis for our idea of the prototype, which had a C-Shaped design. For today's meeting, the first draft for the new prototype design had been completed and we were discussing about the feasibility of it. 

Here is a picture of the new prototype:


Basically, the base of the stand is where the fish tank is to be placed. It is supposed to be expandable sideways to allow fish tanks of different sizes (up to a limit) to be placed onto it. Currently, the expanding technique that is being investigated is sliding with a "lock" mechanism, which locks the base when at the desired length. The reason why we would place the fish tank at the bottom of the tank is because we hope that its weight can be used to support the stand.

The support part (longest height) of the stand is intentionally curved to provide a more aesthetically pleasing and hopefully, stronger base design. However, we are still unsure if this can be made and it is not as important as the previous part (base) of the fish tank, thus we left it aside in the meeting.

Finally, the uppermost part of the fish tank, the tray base, is where the tray containing plants will be put on. We hope that the support is strong enough to support both the plants and the tray base itself. A section has been added under the base, which can be pulled out, for the battery charger to be placed if we would decide to add in the dynamo concept to our invention.

Some measurements have been taken into account for the current sketch.

Hence, our mentor and us ourselves felt that it was a better design than the previous few designs, thus we had confirmed to go along with this design for the stand. All we need to do now is consult Frankie on the possibility of this design!

Tuesday, June 12, 2012

Entry 13: Meeting with Mentor (8)

12 June 2012

Today, our meeting was mainly a discussion on the meeting with Frankie 2 days ago.

First, we brought up the changes in design, then discussed about the originality of our project. Even though we mentioned about the problems of the project, there was nothing much that our mentor could help us with as all of us could not brainstorm for a new idea. At that point of time, there was simply no inspiration and we were feeling quite bad about the project prototype.

However, to cheer us up, our mentor decided to bring us to the biology lab where our plants were being cultivated instead. While taking care of the newly grown plants (which were also cultivated by aquaponics but not with our invention active yet), the group suddenly came up with an idea which seemed more original as well as seeming to look better than the "table" base design.

We thought of a C-shaped base, in which the tank could be placed below and the tray of plants could be placed above. This design was not only better in appeal, but also seemed easier to construct. Hence, we decided to change our design to this with our mentor's approval, and from now we will embark on researching and developing our newly established idea.

A Design Picture of the NEW Prototype:


Sunday, June 10, 2012

Entry 12: Construction Planning (A)

10 June 2012
By Kai Xiang (Destiny CKX)

After contacting Frankie, a construction expert who was helping us construct the prototype, I went down personally to his factory to discuss about the feasibility of the latest prototype.

Frankie, being an engineering expert, pointed out some of the issues of the prototype. They are as follows:

1. The legs of the display base (table) cannot be adjustable. Doing so would weaken the legs, which support the display base, thus causing it to break easily and topple over. However, he mentioned that he would see if it is possible to construct adjustable legs.

2. The display base cannot use the initial "slide" design as a sliding mechanism is
  a. too expensive
  b. tedious and difficult to construct in the time period
  c. there are better alternatives to this

Thus, the current best way would be to use an ordinary table, drill it into half, insert a board in the middle, drill holes into the sides of the table (and into the board), utilising the "Lock and Key" technique to expand the length of the table. However, this could potentially affect the stability of the table. Still, it was worth a try.

3. The custom hydroponics tray, with the input drilled lower than the output (in the widths of the tray), would cause a messy water current within the tray when water is channeled through. This would cause waste products from the aquaponics water to retain in the tray for long periods of time rather than flowing to the filter zone, hence would hinder the process of cleaning the tray, which was supposed to be rather easy. He suggested adding walls to the inner parts of the tray, which can help facilitate a constant directional water flow instead of a messy one.

He also discussed with me about extensions and he inspired me to come out with one new idea that could expand the use of our project:

Mini-turbines could be placed at the water output on the attachment of the fish tank, which would be naturally powered by kinetic energy from the continuous flow of water, thus this would create electricity which can have other functions in the aquaponics system. Frankie suggested for me to go along with this as it is easy to accomplish and a fresh new idea which is useful, thus can help boost our project overall.

The new prototype sketch after returning from the factory looks like this:

Table


Tray


Today's discussion with Frankie was fulfilling, however, Frankie had doubts on the overall "table" design. He felt that there were much cheaper and better alternatives to this. This probably means that we have to risk our creativity using the current prototype or come out with a totally fresh design in the short amount of time given. At least, I now know what opinions a member of the public would have about our prototype. I do hope that we, as a group, can be inspired either to improve heavily on this design or somehow come out with a new design.

Credits:
Thanks to Frankie for all the advice!

Thursday, June 7, 2012

Entry 11: Meeting with Mentor (7)

7 June 2012

Today, we checked on our temporary set up and washed the fish tank. While doing this, my mentor realised that the leca tray we were using seemed to be quite dirty as well as that plant growth was unstable, hence with his help, we came up with the idea of integrating the "IKEA Hydroponics Kit" into the project, acting as a replacement for the present leca tray. 

Here is a picture of the Hydroponics kit:


The advantages of using the new tray are that it is much easier to handle as compared to monitoring the leca kit, as well as allows for better plant growth as there is no presence of overcrowding, which boosts plant growth. However, there are only 6 pits which hold the plants (and very few leca), thus there is a limitation to the amount of the plants that can be grown.

Of course, we did sketches of the new tray and are going to modify it by drilling 2 holes, 1 in the front and 1 in the back to allow water to be transported into and out of the tray via tubes. Therefore, the latest prototype design we have right now is the same as that from the previous post, except with the tray changed to the modified hydroponics kit.



Tuesday, June 5, 2012

Entry 10: Meeting with Mentor (6)

5 June 2012

Today is the first meeting with our mentor in the holidays. The sketches of the display stand of the prototype has been completed. 

Prototype Design:


The prototype's most prominent structure is the display table placed over the fish tank. The table is extendable via a sliding mechanism in the middle, which is made to fit any length of a home-sized fish tank. The legs of the display stand are extendable via lock keys which are then inserted into the holes in the legs when of the desired height (markings will be provided). There are holes on the table which are meant for hanging the terraces, which can contain a different type of plant than the tray on the display stand filled with leca. However, due to the tubing, the limitations of this is that only one terrace can be connected to tube coming from the tube. Thus, only one terrace can be used, while the holes on the edges of the other 3 sides can be used to hook items (in hook baskets) such as fish food. 

The tray on the display stand contains leca, which cultivates plant growth. A tube inlet and outlet are attached on the tray which allows a continuous cyclic flow of water throughout the system to ensure that the water from the fish tank is being transported into and away from the tray of leca (and plants).

So far, the only problem we find with the current design is possibly that this item is considered merely a table,  however, it is true that we will modify it specifically to suit the Indoor Herb Chinampas. Hence, we can consider the problem to be solved already.

We will continue to work on this prototype in the future.

Wednesday, May 23, 2012

Entry 9: Meeting with group members

23 May 2012

Today, the entire group sat down to meet up once again. This meeting was for us to discuss on the progress on finding for the external help as well as for us to set down our work plans for the month of June, which is extremely crucial to the project.

Regarding the progress on finding and getting an external help, Keven and Gordon has been unable to get any help as they do not have any contacts in this area. While Ching Kai Xiang is currently speaking to Frankie, to see whether he is interested in helping us out.

As for the workplan during the June they are as follow:

Details
Due by
Action by
External help found
28/05/2012
All
Confirmation of Prototype
04/05/2012
All
Creation of website
10/06/2012
Keven Loo
Sourcing of materials
11/06/2012
All
Creation of prototype
15/06/2012
All


While here are the confirmed dates for meeting with our Mentor:

Date
Time
Action by
29 May 2012
1400 - 1500 / 1500 - 1600
Ching, Keven
5 June 2012
1400 -  1500 / 1500 - 1600
Ching, Keven
7 June 2012
1400 – 1500 / 1500 - 1600
All
12 June 2012
1400 – 1500 / 1500 - 1600
All

The reason as to why we aim to complete the core of our project during the June Holidays was because it would be when most of us are free and are thus able to commit ourselves to the project as compared to when school reopens where we will have other commitments such as our academics and CCAs.




Tuesday, May 8, 2012

Entry 8: Meeting with Mentor (5)

8 May 2012

Today, the entire group met up within the school library to have a group meeting where we mainly discussed the idea of the "table" aquaponics set up for our invention.

As mentioned previously, there are quite a bit of advantages with regards to a "table" aquaponics set up for our invention, such as this set up being able to provide optimum support for the leca tray, reducing the storage space and allow for more customisation to the set up as compared to previous designs. However, the entire group had uncertainties as this new design could just simply be a table, with the set ups placed above and below it.

Thus we discussed about further modifications could be made, to further improve this design as well as to make it not just a table put together with that of the aquaponics system. After much discussion, we have decided that for this design, instead of just putting the tray of leca at the top and the fish tank at the bottom with the tubing for the system running all over the place, we will drill holes into the top of the table to allow the tubing to pass through, such that it seems neat and presentable. Furthermore, this also empties up the rest of the table space for things to be placed on. This thus brings another additional plus point to this design where it allows for items to be stored on it. This itself is already a modification made to the table, which value adds our prototype.

At this time, we already had a table in mind that we could use and the next step was to start searching for external help who is able to advice us further as to whether this idea was feasible.