Saturday, June 23, 2012

Entry 19: Prototype Construction Completed

23 June 2012

Our prototype has finally been completed and we collected it today. Though we did not administer the construction of our project (left it to Frankie), we planned the entire process as well as materials to be added out.

Hence, with a few new improvements, the prototype looks like this:
Without being attached to planks yet.

Attached to all 3 planks (1 usual, 2 add-ons), maximum length.

The 2 new improvements are as follows:
  1. The "screw and plate" method has been slightly improved. From the pictures, the blackish, long parts at the sides of the base are actually steel clips, which "clips" into the screws on the side of the planks to ensure that the planks are fastened into position. Hence, this makes expanding the base much more convenient, though with a slightly higher charge.
  2. There are additional steel reinforcements between the connection points of the C-shaped part of the prototype. This provides added help for the support plank to support the tray base and remain upright at the same time. This also adds to the cost, but makes the stand a lot stronger.
Hence, the tray will be placed on the tray base while the fish tank will be placed on the base, creating an aquaponics system (of course, with the water pump and tubes for connection). All that is required now is to be sanded, then painted and surfaced to ensure that the wood does not decay when it comes into contact with water. That being said, our first prototype is finally completed!


Wednesday, June 20, 2012

Entry 18: Prototype Construction Begins

20 June 2012

Today, we have sent the finalised prototype sketches to Frankie for the construction of the prototype. Fortunately for us, Frankie helped us with the sourcing of materials in the area around his industry. Though the materials were slightly more costly than we anticipated, it saved us from a lot more hassle and provided more convenience for us.

He also provided us with sources in which these materials (from his shop) could be found, of which most were in line with our research but we had a lack of time to find:
  1. Plywood - Furniture Industry Area
  2. Screws - Any hardware shop
  3. Steel - Customized from his factory
Hence, we would once again like to thank Frankie for helping us and supporting us with the project!

Tuesday, June 19, 2012

Entry 17: Materials and Dimensions Planning

19 June 2012
By Kai Xiang (Destiny CKX)

Today, I had informed my father, an engineering expert, of the almost finalised design, and he decided to guide me along the prototype design. My father and I sat down and discussed seriously about the whole outlook of the prototype, I listened as he provided me with possible improvements to the prototype.

Being an expert, my father provided me with simple yet seemingly effective suggestions to improve the design of our prototype. Together, we confirmed and finalised the dimensions of the prototype, as well as thought of the materials to be used together. At last, there was an astonishing conclusion.

Despite our exhaustion, I managed to take in his suggestions and incoporate it into our prototype. Here are some changes:

The expandable base design has once again changed, but this time requires fewer materials and has a simple and firm design. Instead of using the sliding mechanism, which he said was difficult to build under the small amount of time we had, he suggested that we use a "screw and plate" method for the extension of our base.

Simply put, we would screw a hole into each of the planks (listed below are the planks), then to adjust the base to the desired length, we simply use a steel bar to secure the planks together and screw screws into the base and planks through the steel bar to ensure that the the length of the base is fixed. It was shockingly simple, yet practical and easy to create. Furthermore, it fit the theme of the expandable base well, thus we decided to go along with this design.

Here is how it looks:


If one wishes to adjust the base to the smallest length, then simply use the first (left-most) and last (right-most) plank and screw them together with the bar to fasten them.


He also suggested that to ensure the tray base can be supported by the supporting plank, steel brackets can be used to support it.

Here is how it looks:
The planks of the base will be made of plywood (economical and of decent quality) and be connected to each other via screws.

Hence, these are the small but essential changes we have made to the base.

Here are the dimensions we have set:


Finally, after many painstaking processes and meaningful experiences, we have a finalised design for the base! After reviewing all that the group has been through, it really provides a sense of elation that we have completed our objectives!

Credits:
Thanks to my father, who supported me and criticised the design, as well as suggesting improvements with his experiences in this field!





Entry 16: Sourcing for Materials@IKEA

19 June 2012

Today, we went to IKEA Tampines to source for the materials and measure the costs to build our prototype. Our objective was mainly to confirm the expendable mechanism which we are using as well as the  cost and quality of wood used.

The first things that caught our eyes were metal poles. These metal poles were made of stainless steel, which prevented rusting of the stand, and this allowed us to come up with a plan for the expendable base.

This is how it looks:


Basically, there will be squarish parts connected to both ends of the metal poles. The wood we will use is specially carved to the shape above, in which the internal part fits the squarish part on the pole but the hole on the surface of the blocks do not fit the square on the pole to prevent it from sliding out.

We named the corner blocks block 1 and 2. Basically, we would make the squarish parts of the poles in block 2 fixed, whereas the squarish parts of the poles in block 1 are confined to the space within the block but can move from one end to the other. This allows the base to be expandable. Thus, the support structure will be placed on block 1 instead of between block 1 and 2 to make the design more practical. When the base is expanded, the poles are exposed. Hence, we use block "add-ons" to be placed over the poles to cover them up as well as to act as support for larger tanks. We have planned for 2 "add-ons" to be included in our design, thus our base can now fit fish tanks of 3 different lengths.

However, there are a few problems in the design. Firstly, we have no idea who to ask on how to carve internal shape of the wooden blocks 1 and 2. Even if we had help, the expertise required for carving such intricate designs would not come cheap. Next, we had no idea where to find the squarish parts on the end of the poles and how to connect them at all. Thus, we were left with a few loopholes for this idea.

We also came up with major dimensions for the stand. We decided to confirm this only after we had found all the materials required.

We then decided to search for wooden parts for the base. However, our efforts were in vain as we realised that isolated wooden planks could not be found in IKEA and only wooden furniture (self-service packaging types) could be found. Hence, nothing much could be resolved.

Even though we tried our best today, nothing much was resolved. Hence, we hope that we are able to source for materials with greater luck and efficiency the next time.

Friday, June 15, 2012

Entry 15: Construction Planning (B)

15 June 2012

Today, we went to Frankie's factory to discuss about our new prototype design. Surprisingly, Frankie approved of the new design and praised it, albeit a few minor parts, and gave us suggestions on how to improve it again.

From our initial design, he gave 2 important suggestions.

First, he suggested that the extendable part of the tray base be removed from the tray design. This is because  the extendable tray actually has no true function on the tray base itself and would be a hassle, as well as cost high, to construct onto my tray base. Not only that, but it also limits the amount of space that we can use for a dynamo-lighted bulb which is currently an extension we are looking it. Hence, we took his advice and scrapped off this part of the design.

Second, he suggested that we use strings to make the base expandable. This is because the method is practical and cheap, though our aesthetics would be slightly, not significantly, affected by this. We took this advice into consideration but are currently unsure if we should use it. Still, it was better than the initial idea we had.

Frankie also helped us with sourcing of materials to construct this prototype. He told us that IKEA was a good place to look for cheap and reliable DIY materials. Hence, we are now planning a trip to IKEA Tampines, a warehouse of IKEA which contains a variety of furniture and creatively designed household items.

Our newest prototype design now looks like this:



Hence, today's visit to Frankie's factory was fruitful as we finally settled on a design and to make things better, Frankie told us that the cost of this new design would be much cheaper than the previous one! Now, all we have to do is source for the materials and finalise the expanding mechanism for the base of the stand.

Credits:
Once again, thanks to Frankie for helping us with our prototype design!

Thursday, June 14, 2012

Entry 14: Meeting With Mentor (9)

14 June 2012

Today, our meeting was about the new prototype design.

Previously, we had formulated the basis for our idea of the prototype, which had a C-Shaped design. For today's meeting, the first draft for the new prototype design had been completed and we were discussing about the feasibility of it. 

Here is a picture of the new prototype:


Basically, the base of the stand is where the fish tank is to be placed. It is supposed to be expandable sideways to allow fish tanks of different sizes (up to a limit) to be placed onto it. Currently, the expanding technique that is being investigated is sliding with a "lock" mechanism, which locks the base when at the desired length. The reason why we would place the fish tank at the bottom of the tank is because we hope that its weight can be used to support the stand.

The support part (longest height) of the stand is intentionally curved to provide a more aesthetically pleasing and hopefully, stronger base design. However, we are still unsure if this can be made and it is not as important as the previous part (base) of the fish tank, thus we left it aside in the meeting.

Finally, the uppermost part of the fish tank, the tray base, is where the tray containing plants will be put on. We hope that the support is strong enough to support both the plants and the tray base itself. A section has been added under the base, which can be pulled out, for the battery charger to be placed if we would decide to add in the dynamo concept to our invention.

Some measurements have been taken into account for the current sketch.

Hence, our mentor and us ourselves felt that it was a better design than the previous few designs, thus we had confirmed to go along with this design for the stand. All we need to do now is consult Frankie on the possibility of this design!

Tuesday, June 12, 2012

Entry 13: Meeting with Mentor (8)

12 June 2012

Today, our meeting was mainly a discussion on the meeting with Frankie 2 days ago.

First, we brought up the changes in design, then discussed about the originality of our project. Even though we mentioned about the problems of the project, there was nothing much that our mentor could help us with as all of us could not brainstorm for a new idea. At that point of time, there was simply no inspiration and we were feeling quite bad about the project prototype.

However, to cheer us up, our mentor decided to bring us to the biology lab where our plants were being cultivated instead. While taking care of the newly grown plants (which were also cultivated by aquaponics but not with our invention active yet), the group suddenly came up with an idea which seemed more original as well as seeming to look better than the "table" base design.

We thought of a C-shaped base, in which the tank could be placed below and the tray of plants could be placed above. This design was not only better in appeal, but also seemed easier to construct. Hence, we decided to change our design to this with our mentor's approval, and from now we will embark on researching and developing our newly established idea.

A Design Picture of the NEW Prototype: